Showers

  • Showers ‣ with manual
    Cleaning device ‣ Nozzle-Spray showers

    • Can be used in freshwater, clear-water and backwater applications.
    • Considerable freshwater savings and low water consumption.
    • Immediate cleaning of the nozzles during operation while removing dirt at the same time.
    • Easy operation; just turn the handwheel and the cleaning device moves both axially and radially so that the dirt is removed via the valve which has now opened.
    • High nozzle efficiency.
    • Easy nozzle removal. The nozzles are made of high molybdenum stainless steel 1.4439 and are available in a variety of sizes and types to suit all shower applications.
    • It is easy to alter the type of nozzle (fan-jet and needle-jet) as well as nozzle size.
    • Nozzles are firmly attached to the shower.
    • Easy adaptation to each shower application.
    Product Inquiry

     

     

  • Showers ‣ with manual
    Cleaning device ‣ Brush

    The perfect brush for efficient spray-shower cleaning.

    Cleaning devices are the simplest and most process-reliable solution, in order to achieve a good spray, even with water contaminated with fibers and suspended solids. The efficiency is largely determined by the choice of the brush.

    Whether stainless steel or syntetical bristles, whether welded, screwed or directly pulled in bristles - we will find the perfect solution for you.

    Product Inquiry

  • Showers ‣ with automatical
    Cleaning device ‣ Valve 10.900

    • Regular cleaning of nozzles thanks to automatic operation of the cleaning device
    • Celaning cycle ("open valve", "rinse shower", "close valve") at freely programmable intervals
    • Firm closure of valve with a defined closing force
    • Existing showers can be retrofitted with this device

    Download Datasheet

    Product Inquiry

  • Showers ‣ without
    Cleaning device ‣ Tailor-made showers

    A cleaning device is not always mandatory or even possible. We also help you solve complex problems.

    Product Inquiry

Drive Units

  • Drive Units ‣ Oil-Hydraulically ‣ conventionally controlled ‣ 10.094

    For the effective, uniform and streak-free cleaning of wires and felts with manual adjustment of the stroke speed.

    Benefits

    • Controlled cleaning of wires, felts and rolls in paper and board machines
    • Adjustable stroke speed
    • Linear, uniform oscillation with instant reversal at the end points

    Principle and Design

    • Double-acting hydraulic cylinder

    Technical details:

    Thrust: 15.000 N  
    Stroke: infinitely adjustable in a range of  1 to 200 mm
        1 to 300 mm (optional)
        1 to 500 mm (optional)
    Oil-pressure:  30 to 70 bar (3 to 7 MPa)  

     

    Product Inquiry
    Predecessors State Manual
    10.0191 (prior: 10.191S) available E-Mail
    10.0591 (prior: 10.591S) available E-Mail

  • Drive Units ‣ Oil-Hydraulically ‣ electronically controlled ‣ 10.093

    For the effective, uniform and streak-free cleaning of wires and felts with automatic adjustment of the stroke speed to the paper machine speed

    Benefits

    • Synchronized, controlled cleaning of wires, felts and rolls in paper and board machines
    • Computer-controlled, automatic adjustment of the stroke speed to the paper machine speed, the wire or felt lengths and the jet width (jet-to-jet cleaning)
    • Linear, uniform oscillation with instant reversal at the end points
    • Adjustable change of reversal points (stroke offset)
    • Adjustable, cyclical staggering of reversal points
    • Adjustable fast return speed option
    • Integrated oscillation monitoring system with safety switchoff
    • Minimum energy consumption

    Principle and Design

    • Double-acting hydraulic cylinder with transsonar sensor
    • Electronic oil flow control valve for automatic adjustment of stroke speed
    • Electronic operation control and monitoring, easy entry of parameters into the control system

    Technical details:

    Thrust: 15.000 N  
    Stroke: infinitely adjustable in a range of  1 to 200 mm
        1 to 300 mm (optional)
        1 to 500 mm (optional)
    Oil-pressure:  30 to 70 bar (3 to 7 MPa)  

    Download Datasheet

    Product Inquiry
    Predecessors State Manual
    10.0192 (prior: 10.191 / 10.691) available E-Mail
    10.0691 (prior:10.691 S) available E-Mail

  • Drive Units ‣ Electrically ‣ conventionally controlled ‣ 10.010 LE-R

    For the effective, uniform and streak-free cleaning of wires and felts with automatic adjustment of the stroke speed to the paper machine speed

    Benefits

    • Synchronized, controlled cleaning of wires, felts and rolls in paper and board machines
    • Automatic adjustment of the stroke speed to the paper machine speed, the wire or felt length (jet-to-jet cleaning) by means of a frequency converter possible
    • Oscillation monitoring with safety switchoff available
    • Linear, uniform oscillation with instant reversal at the end points
    • Oscillator and shower bearing are one compact system
    • Minimum energy consumption

    Principle and Design

    • Electrical gear motor (IP 67), slip hub and double-screw spindle
    • Oscillation by conversion of the uniform rotation of the double-screw spindle into a stroke movement
    • Constant or infinitely adjustable stroke speed (by means of a frequency converter)
    • Switching blade and bracket for proximity switch for oscillation monitoring
    Drive unitType 2"-3"Type 4"-6"
    Recomeded shower size    between 2" and 3" between 4" and 6"
    Stroke 206,4 mm or 301,4 mm     203,2 mm or 304,2 mm
    Stroke speed 1 to 120 mm/min
    Voltage/frequency On customer request

     Download Datasheet

    Product Inquiry
    Predecessors State Manual
    10.510 LSE-R / LE-R available E-Mail
    10.500 LSE / LSE-R / LE-R Spare parts available E-Mail

  • Drive Units ‣ Electrically ‣ electronically controlled ‣ 10.020 EC

    The 10.020 EC is our robust and generously dimensioned drive unit for machines and positions where service is problematic. By the above-average reserves he reaches an otherwise unattainable duration and stability.

    Technical data:

    Thrust: 15.000 N  
    Stroke length: infinitely adjustable in a range of 1 to 200 mm
        1 to 300 mm (optional)
    Supply voltage:   24 V DC  

    Download Datasheet

    Product Inquiry
    Predecessors State Manual
    10.500 EC (G1 since 1995: 5x 24V; PL50) Spare parts not avaialble E-Mail
    10.510 EC (G2 since 1997: 3x230V; PL50) Spare parts on request E-Mail
    10.510 EC (G3 since 2001: 3x 24V; PL50) Spare parts on request E-Mail
    10.020 EC (G4 since 2008: 3x 24V; PLE80) Available E-Mail

    Every generation can be converted to latest technology.

  • Drive Units ‣ Electrically ‣ electronically controlled ‣ LEO 107 / 107 P / IL

    The LEO is our all-time-available drive. With intelligent stock-keeping and a focus on service, we achieve a very short reaction time. We also offer maintenance contracts for our LEO.

    Our LEO thus offers calculable costs with maximum availability.

    Product Inquiry

  • Drive Units ‣ Electrically ‣ electronically controlled ‣ SERVO 350 / 1400 / 2000

    The idea behind the latest STAMM Cleantech product - SERVO - is the integration of drive control into the process control system of the paper machine.

    The linear electronic oscillator communicates with state-of-the-art Profibus technology and can be connected to the existing process control system based on defined interfaces.

    The system is delivered in a small control box and includes a 5 inch touch screen as well as the corresponding wiring and documentation.

    The SERVO system is designed, that up to 10 drives can be controlled individually via a control box.

    The Cleantech principles of jet-to-beam cleaning also applies to the SERVO. The always optimally adapted oscillating speed improves the cleaning effect, since the entire surface of the fabric is cleaned in the shortest possible time.

    This STAMM Cleantech innovation has set a new standard in oscillation technology.

    Product Inquiry

  • Drive Units ‣ Drive with Bearing ‣ Crank Drive Oscillator

    Wire cleaning in stock preparation and waste water treatment

    For oscillation of chemical injection pipes and spray pipes for roll cleaning

    Benefits

    • Very robust and reliable
    • Little maintenance requirement

    Principle and design

    The rotary motion of a worm-gear motor is transferred into an oscillation movement via a crank with sliding block and sliding guide.

    Download Datasheet

    Download Datasheet (version in stainless steel)

    Product Inquiry

Bearings

  • Bearings ‣ Conventional Bearings ‣ 10.800 Oscillator bearing

    • straightforward bearing with low wear
    • completely made of stainless steel
    • various mounting positions possible
    • simple and fast assembly / disassembly of the drive unit
    • various drive variants selectable:
    • subsequent replacement of existing drive unit possible
    • easy maintenance
    Product Inquiry
    Predecessor State EBW
    STAMM Bronze-bearing Spare-parts available E-Mail

Nozzles

  • Nozzles ‣ Low-pressure
    Flat-Jet ‣ Stainless steel nozzle plates

    The STAMM nozzle plates are subjected to a regular quality control check of spraying angle and water consumption. To ensure jet formation, the water pressure should be at least 1.5 bar.

    There is a whole range of different jet sizes and types for all applications (cleaning, conditioning, knockoff etc.). We provide our flat-jet nozzles with an angle of 30°, 60° and 75°

    All STAMM nozzles are made of high molybdenum stainless steel 1.4435.

    Special materials are also available:

    • nozzles made of titanium for very corrosive applications
    Product Inquiry

  • Nozzles ‣ Low-pressure
    Flat-Jet ‣ Ceramic nozzle ‣ ICF

    The times of complicated installation and removal of flat jet nozzle plates and associated separate thread rings is finally over with this intelligent nozzle system.

    The STAMM Cleantech ICF is designed that the preset spray angle no longer changes when the nozzle is tightened. Simply

    • Insert the complete nozzle into the nozzle holder and screw it in by hand
    • adjust the jet angle with the supplied tool and
    • tighten with a standard hexagonal key

     - done!

    The ceramic material, which was first installed in a low-pressure nozzle, is extremely wear-resistant. You benefit from the advantages of ceramics:

    • Significantly longer life
    • Significantly lower water consumption over the time

     

     

    Product Inquiry

  • Nozzles ‣ High-pressure
    Needle-Jet ‣ Stainless steel nozzle plate

    The STAMM nozzle plates are subjected to a regular quality control check of spray-quality and water consumption. To ensure jet formation, the water pressure should be at least 1.5 bar.

    We provide a whole range of different jet sizes for all applications. Our needle-jet nozzles are available spraying at an angle of 90°, jet spraying at an angle of 27°, or jets spraying from two sides at an angle of 27°

    All STAMM nozzles are made of high molybdenum stainless steel 1.4435.

    Special materials are also available:

    • nozzles made of titanium for very corrosive applications
    Product Inquiry

  • Nozzles ‣ High-pressure
    Needle-Jet ‣ Stainless steel mono nozzle

    The STAMM mono nozzles offer easy assembly and disassembly even under difficult installation conditions with the proven loss protection through patch-coating.

    The STAMM nozzle plates are subjected to a regular quality control check of spray-quality and water consumption. To ensure jet formation, the water pressure should be at least 1.5 bar.

    We provide a whole range of different jet sizes for all applications.

    All STAMM nozzles are made of high molybdenum stainless steel 1.4439 (4% to 5% molybdenum content).

    Special materials are also available:

    • nozzles made of titanium for very corrosive applications
    Product Inquiry

  • Nozzles ‣ High-pressure
    Needle-Jet ‣ Rubynozzle plate

    The ruby ​​insert guarantees optimal spray quality over a long period of time.

    The STAMM Cleantech nozzle plates are subjected to a regular quality control check of spray-quality and water consumption. To ensure jet formation, the water pressure should be at least 1.5 bar.

    We provide a whole range of different jet sizes for all applications.

    Product Inquiry

  • Nozzles ‣ High-pressure
    Needle-Jet ‣ ICL-R

    The ruby ​​insert guarantees optimal spray quality over a long period of time.

    The STAMM Cleantech ICL-R nozzles are subjected to a regular quality control check of spray-quality and water consumption.

    We provide a whole range of different jet sizes for all applications.

    The ICL-R nozzle is a one-piece insoluble connected HD nozzle made of stainless steel with ruby ​​insert.

    Our customers can conveniently access the cost-effective in-house nozzle-service. The nozzle-service for the ICL-R includes function checks, cleaning and, if necessary, replacement of the noozle.

    External thread: M 30 x 1,5 and M 32 x 1,5
    Wrench size: SW 19, hexagonal
    Nozzle diameter: 0,4/0,7/0,9

    Product Inquiry

  • Nozzles ‣ High-pressure
    with ​​insert ‣ ICS-R

    The ruby ​​insert guarantees optimal spray quality over a long period of time.

    Using the refining process (TROVALIZATION), the surface of the ICS-R nozzle is mirror-smooth, so that contamination and calcification are hardly possible.

    The STAMM Cleantech ICS-R nozzle convinces with time-saving handling (very fast installation / removal) and special corrosion resistance.

    Another advantage of the STAMM Cleantech ICS-R nozzle is the replaceable ruby ​​insert. Our customers can conveniently access the cost-effective in-house nozzle-service. The nozzle-service for the ICS-R includes function checks, cleaning and, if necessary, replacement of the insert.

    With these properties, the STAMM Cleantech ICS-R offers the optimum solution for a low-maintenance production process - in the interests of its customers.

    External thread: M 30 x 1,5 and M 32 x 1,5
    Internal thread: M 20 x 1,0
    Wrench size: SW 19, hexagonal
    Nozzle diameter: 0,4/0,7/0,8/0,9

    Product Inquiry

  • Nozzles ‣ High-pressure
    with ​​insert ‣ ICS

    The high-performance ceramics guarantee optimum spray quality. An extremely high material hardness is achieved by the special networking of the ceramic globules.

    Using the refining process (TROVALIZATION), the surface of the ICS nozzle is mirror-smooth, so that contamination and calcification are hardly possible.

    The STAMM Cleantech ICS nozzle convinces with time-saving handling (very fast installation / removal) and special corrosion resistance.

    Another advantage of the STAMM Cleantech ICS nozzle is the replaceable ceramic insert. Our customers can conveniently access the cost-effective in-house nozzle-service. The nozzle-service for the ICS includes function checks, cleaning and, if necessary, replacement of the insert.

    With these properties, the STAMM Cleantech ICS offers the optimum solution for a low-maintenance production process - in the interests of its customers.

    External thread: M 30 x 1,5 and M 32 x 1,5
    Internal thread: M 20 x 1,0
    Wrench size: SW 19, hexagonal
    Nozzle diameter: 0,4/0,7/0,8/0,9

    Product Inquiry